ALLEN & HEATH iDR-4 User's Guide download pdf (Page 16)

16 IDR-4 User Guide

Starting Offline with iDR System Manager Software

You need to install the iDR System Manager software on your

PC. This requires Windows™ 95, 98, NT, ME, 2K or XP. We

recommend that you check the Allen & Heath web site for the

latest version. We are continually updating our software to add

new features or make improvements. Download the latest

version from our web site.

IMPORTANT: Do not install this software over a

previous version. The setup utility will install the iDR System

Manager into its own directory so that previous versions can be

retained. A previous version can be uninstalled using the

Windows™ Control Panel Add/Remove Programs application.

Run the self-extracting .exe file to install the software. Follow

the on-screen instructions. Make sure you read the Release

Notes before running the program. These may contain

important information about the new software version.

Start the iDR System Manager from the Start / Programs / Allen

& Heath menu. To open a new session click on the blue icon,

press Ctrl+N, or open the N

ew item in the File menu. Select

“Offline iDR-4” to start an offline session to get familiar with the

program before you connect the iDR-4 unit. Use the H

elp

menu to learn more about how the software works. You can

archive your settings to load into the iDR-4 later.

Turning the iDR-4 On and Off

Make sure you have read the Important Safety

Instructions printed earlier. Also check that your local

mains supply is compatible with that printed on the rear

panel of the iDR-4. Ensure that the correct mains lead with

moulded plug and IEC connector has been supplied.

To avoid any unexpected audible clicks or thumps

always turn connected power amplifiers down or off before

switching the iDR-4 or any other signal equipment on or off.

Turn the unit on by pressing the rear panel power ON/OFF

switch. The LCD display lights up and the message ‘Please

wait…’ is displayed while the processor boots up. This is

followed by a ‘Recall ..’ message if a power-up patch is active.

Finally, the normal display is shown.

Note that ‘normal’ display and control settings depend on the

last configuration loaded and whether a power-up patch has

been set.

Boot up time is normally around 10 seconds. However,

this can be up to 35 seconds if the front panel menu *5.1

DHCP Setup has been set to YES and the unit is not connected

to a DHCP network.

Parameters restored on power-up The iDR-4

remembers its unit name and address settings on power up.

The clock is always running so the correct time and day is

retained. Configuration related parameters such as channel

names, stereo linking and scheduled events are restored.

Patch related parameters such as levels, EQ and soft control

settings are recalled only if a power-up patch containing them

has been set. If not, then all patch related parameters are reset

according to factory default. Further details are provided in the

section about Patches later in this user guide, and in the iDR

System Manager Help file.

Allen & Heath

Wed 13:44:08

Please wait...

IMPORTANT: The iDR does not recall

its last settings on power up. It initialises to

reset state or recalls a ‘power up’ patch if one

has been set. Read here >>>>>>>>>

CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.

FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE WITH SAME TYPE AND RATING.

ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES.

47-63Hz ~ 75W MAX

100 - 240V~

THIS APPARATUS MUST BE EARTHED.

WARNING

AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.

FUSE: T1.6AL

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 47 48

Comments to this Manuals

No comments

ALLEN & HEATH iDR-4 User's Guide Page 16

Comments to this Manuals

Related products and manuals for Audio cards ALLEN & HEATH iDR-4