ALLEN & HEATH ML5000 User's Guide Page 26
- Page / 60
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
26 ML5000 User Guide
C MAIN MIX D INPUT FADERS
C1 MAIN MIX. A single switch routes the
channel signal to the 3 output main mix. Its balance
and image within the L, R and C outputs is
determined by the BLEND and PAN controls.
C2 BLEND. This control adjusts the balance
between the LR and C outputs. Fully anti-clockwise
all the signal routes to the LR outputs and none to
C. At the detented centre position the signal routes
equally to the LR and C outputs. Fully clockwise all
signal routes to the C output and none to LR.
BLEND does not affect the group routing. The
control has a 3dB attenuation at centre position.
The stereo channels route stereo to LR and sum
the signal in mono to C.
C3 PAN. Adjusts the balance between the L and
R outputs. It does not affect the C output. At the
detented centre position the signal routes equally to
L and R. PAN and BLEND combine to adjust the
balance between the 3 outputs. PAN also adjusts
the balance between odd and even groups if the
GRP PAN ON switch is selected. The control has a
3dB attenuation at centre position.
C4 GRP PAN ON. In the up position the groups
are sourced pre-pan. Use this setting for creating
mono groups not affected by the position of the
PAN control. When pressed, the groups are
sourced post-pan. Use this setting for creating
stereo groups where the signal is balanced between
L and R using the PAN control.
D1 IDENT STRIP. Identifies the channel
numbers and provides a write-on area. The use of
low adhesion artist or masking tape is
recommended.
D2 MUTE. This momentary action switch turns
the channel signal on or off. Both pre and post-fade
signals are affected unless the pre-fade pre-mute
setting has been internally configured. The channel
can also be muted by the mute groups, VCA group
mutes, snapshot memories, solo-in-place and MIDI
note on/off messages. The switch illuminates when
the channel is muted.
The switch also functions as a solo select when the
console is in SIP mode, and as an edit key when in
EDIT GROUPS or EDIT SAFES mode. The
channel mute status is always displayed on the
switch regardless of mode.
24
5
7
GROUP
8
VCA
6
4
3
2
1
PAFL
MUTE
PK
-6
SIG
+6
0
SAFE/EDIT
LR C
=
LR
=
PAN
MAIN
MIX
LCR
BLEND
+
OO
30
5
0
10
5
40
10
20
- USER GUIDE 1
- Introduction 2
- Contents 3
- Limited One Year Warranty 4
- General Precautions 6
- ML5000 Key Features 7
- QUICK START SHEET 8
- Using LCRplus™ 8
- To Clear or Set All : 9
- Using P/AFL : 9
- Problems ? 9
- 10 ML5000 User Guide 10
- ML5000 User Guide 11 11
- Technical Specifications 12
- ML5000-48 = 2106 13
- ML5000-40 = 1851 13
- ML5000-32 = 1596 13
- ML5000-24SC = 831 13
- Connecting the Power Supply 14
- Earthing 15
- Rear Panel Connections 16
- 18 ML5000 User Guide 18
- Gain Structure 19
- CONTROL LAYOUT 20
- A MONO INPUT and EQ 22
- Using the Filter 22
- Using the Equaliser 23
- B GROUP / AUXILIARY SENDS 24
- Internal Link Options 25
- Using the GRP/AUX Sends 25
- Removing the Fader 27
- Using LCRplus 28
- E STEREO INPUT and EQ 30
- Using the Dual Inputs 31
- Using Mono Sources 31
- 32 ML5000 User Guide 32
- H ROTARY AUX 1-8 MASTERS 34
- Configuring Groups and Auxes 34
- I MAIN MIX MASTERS 35
- J MATRIX and 2-TRACK 36
- 2-TRACK Output 36
- Using the Matrix 37
- K VCA GROUPS 38
- VCA Groups Explained 38
- The benefits of VCA grouping 38
- Using VCA Groups 39
- Using PAFL 39
- To Assign a VCA Group 40
- SELECT GROUP TO EDIT 41
- ASSIGN USING CH MUTES 41
- M SNAPSHOT MEMORIES 42
- A Note on Snapshot Mutes 42
- Snapshots Explained 42
- STATUSMIDI RS232 43
- Previewing Snapshot Memories 44
- To Store a Snapshot Memory 44
- To Disable Store 44
- To Recall a Snapshot Memory 45
- Turning all Mutes On or Off 45
- Using Snapshot Memories 45
- N SOLO-IN-PLACE 46
- Solo-In-Place Explained 46
- Solo Safes Explained 47
- Making a Channel Solo Safe 47
- Using Solo-In-Place 47
- The Console Monitor System 48
- The Monitor Logic 48
- Q OSC/NOISE GENERATOR 50
- R INTERCOM 51
- The Intercom Explained 51
- S TALKBACK 52
- Using Talkback 52
- The Console Meterpod 53
- Meter Types 54
- Changing from LRC to LCR 54
- 9 Recall snapshot memories 55
- Channel Mutes 56
- Snapshot Memories 56
- MIDI AFL Messages 56
- 58 ML5000 User Guide 58
- USER NOTES : 59
- 60 ML5000 User Guide 60
- Visit Allen & Heath : 60
© 2020, manymanuals.com. All rights reserved. | 0.555 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals