ALLEN & HEATH ML5000 User's Guide Page 40
- Page / 60
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
40 ML5000 User Guide
K4 VCA GROUP FADER. The fader adjusts the
level of all channels assigned to the group. The ‘0’
position is referred to as the ‘nominal’ operating
setting. At this position the channel levels are as
marked on the channel faders. Any adjustment
made to the group fader offsets the channel level by
that amount. It is best to start with the group faders
set to their ‘0’ position.
At minimum position the fader shuts off all assigned
channels. At maximum position it provides a further
+10dB boost. Note that the maximum boost that
may be applied to the channel VCA is +20dB
regardless of how many group faders are assigned
and set above ‘0’.
The following diagrams illustrate the combined
channel gain when assigning more than one VCA
group. In this case the final gain is affected by the
channel fader and three VCA groups.
Example 1. A 0dBu signal is passed through the
channel. The fader attenuates this by 5dB. Group1
attenuates it by a further 10dB to –15dBu. Group2
boosts by 5dB bringing it up to –10dBu. Group3 is
set to ‘0’ resulting in the final level of –10dBu.
Example 2. Once again the channel fader
attenuates the signal to –5dBu. However, Group1
is set to minimum turning the signal off. There is no
output regardless of the setting of Groups 2 and 3.
Example 3. Here the channel fader and Groups 1
and 2 faders are set for +10dB boost. The result is
the channel VCA reaching its maximum of +10dB
regardless of the combined 30dB boost. It is best to
work with the faders around ‘0’ and avoid excessive
boost.
K5 EDIT GROUPS. Press this switch to put the
console into edit groups mode. The red LED
flashes to warn that the console is in edit mode.
Press at any time while the LED is flashing to
restore normal operating mode. All the VCA group
MUTE LEDs K1 and channel SAFE/EDIT LEDs
D3 turn off when edit mode is first entered. This
means that no group is selected for editing.
The same edit groups mode is used to edit both the
mute and VCA groups. Pressing the associated
master switch while in edit mode selects the mute
group or VCA group you want to edit.
Only one group may be edited at a time. The
current assignments for all groups are always
displayed on the channel VCA assign LEDs D6 .
To Assign a VCA Group
Press EDIT GROUPS K5 . Next, press the MUTE
switch K1 for the group you want to edit. Both
switches flash. The channel SAFE/EDIT LEDs D3
display which channels are currently assigned to
the group. Now press the channel MUTE switches
D2 to toggle channels in or out of the group. Press
EDIT GROUPS again to exit edit mode, or press
another group mute switch to edit a different group.
To clear all channels in a VCA group
While in edit mode, hold down SHIFT M9 and
press RECALL M7 . The recall switch flashes and
the display flashes CLr. Release shift and press
RECALL again to confirm. All channel SAFE/EDIT
LEDs turn off indicating that the group is cleared.
To assign all channels to a VCA group
While in edit mode, hold down SHIFT M9 and
press RECALL M7 two times until the display
flashes SEt. Release shift and press RECALL
again to confirm. All channel SAFE/EDIT LEDs turn
on indicating that all channels are assigned.
RECALL
CLR/SET
ALL
(SHIFT)
CHANNEL GROUP 1 GROUP 2 GROUP 3
+10
+5
0
-5
-10
-15
-20
-40
off
-30
IN
OUT
0dB
-10dB
+15
+20
-5
-10
+5
0
CHANNEL GROUP 1 GROUP 2 GROUP 3
+10
+5
0
-5
-10
-15
-20
-40
off
-30
IN
OUT
0dB
off
+15
+20
-5
off
+5
0
Example 1
Example 2
CHANNEL GROUP 1 GROUP 2 GROUP 3
+10
+5
0
-5
-10
-15
-20
-40
off
-30
IN
OUT
0dB
+10dB
+15
+20
+10 +10 +10
0
(max)
Example 3
- USER GUIDE 1
- Introduction 2
- Contents 3
- Limited One Year Warranty 4
- General Precautions 6
- ML5000 Key Features 7
- QUICK START SHEET 8
- Using LCRplus™ 8
- To Clear or Set All : 9
- Using P/AFL : 9
- Problems ? 9
- 10 ML5000 User Guide 10
- ML5000 User Guide 11 11
- Technical Specifications 12
- ML5000-48 = 2106 13
- ML5000-40 = 1851 13
- ML5000-32 = 1596 13
- ML5000-24SC = 831 13
- Connecting the Power Supply 14
- Earthing 15
- Rear Panel Connections 16
- 18 ML5000 User Guide 18
- Gain Structure 19
- CONTROL LAYOUT 20
- A MONO INPUT and EQ 22
- Using the Filter 22
- Using the Equaliser 23
- B GROUP / AUXILIARY SENDS 24
- Internal Link Options 25
- Using the GRP/AUX Sends 25
- Removing the Fader 27
- Using LCRplus 28
- E STEREO INPUT and EQ 30
- Using the Dual Inputs 31
- Using Mono Sources 31
- 32 ML5000 User Guide 32
- H ROTARY AUX 1-8 MASTERS 34
- Configuring Groups and Auxes 34
- I MAIN MIX MASTERS 35
- J MATRIX and 2-TRACK 36
- 2-TRACK Output 36
- Using the Matrix 37
- K VCA GROUPS 38
- VCA Groups Explained 38
- The benefits of VCA grouping 38
- Using VCA Groups 39
- Using PAFL 39
- To Assign a VCA Group 40
- SELECT GROUP TO EDIT 41
- ASSIGN USING CH MUTES 41
- M SNAPSHOT MEMORIES 42
- A Note on Snapshot Mutes 42
- Snapshots Explained 42
- STATUSMIDI RS232 43
- Previewing Snapshot Memories 44
- To Store a Snapshot Memory 44
- To Disable Store 44
- To Recall a Snapshot Memory 45
- Turning all Mutes On or Off 45
- Using Snapshot Memories 45
- N SOLO-IN-PLACE 46
- Solo-In-Place Explained 46
- Solo Safes Explained 47
- Making a Channel Solo Safe 47
- Using Solo-In-Place 47
- The Console Monitor System 48
- The Monitor Logic 48
- Q OSC/NOISE GENERATOR 50
- R INTERCOM 51
- The Intercom Explained 51
- S TALKBACK 52
- Using Talkback 52
- The Console Meterpod 53
- Meter Types 54
- Changing from LRC to LCR 54
- 9 Recall snapshot memories 55
- Channel Mutes 56
- Snapshot Memories 56
- MIDI AFL Messages 56
- 58 ML5000 User Guide 58
- USER NOTES : 59
- 60 ML5000 User Guide 60
- Visit Allen & Heath : 60
© 2020, manymanuals.com. All rights reserved. | 0.564 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals